Last Modified: 11-29-2007 1.6 A
Service Category: Vehicle Exterior Section: Exterior Panels/Trim
Model Year: 2008 Model: Sequoia Doc ID: RM0000023BV006X
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): INSTALLATION (2008 Sequoia)

INSTALLATION

1. INSTALL NO. 1 BLACK OUT TAPE

(a) Application precautions.

(1) Application temperature.

  • If the temperature is below 15°C (59°F), using an infrared light, heat the base (body attachment surface) and black out tape up to between 20 and 30°C (68 and 86°F). If the temperature is over 35°C (95°F), perform the operation after lowering the temperature to below 35°C (95°F).

    HINT:

    • The most suitable temperature for applying the black out tape is 25°C (77°F).
    • The black out tape cannot be applied correctly at low temperatures due to its stiffness and weak adhesion. The tape loses its consistency at high temperature.

(2) Pre-application procedure.

  • Any uneven twisting or dust on the base (body attachment surface) causes a defective appearance due to air being trapped under the black out tape during application. Make sure that there is no uneven twisting or dust on or around the base or black out tape.

    HINT:

    When the air is dry in winter, put cardboard between the pieces of black out tape and keep them in a dry flat place.

(3) Handling.

  • Keep the black out tape in a dry, flat, and level place because it is easily deformed.

    NOTICE:

    Do not fold, bend or expose the tape to high temperatures.

(4) Application method (method of squeegee operation and application for general portions).

NOTICE:

  • The positioning accuracy must be within 1 mm (0.039 in.) when starting the application. Otherwise, poor appearance and adhesion will result.
  • Do not reuse black out tape that has been removed. Reuse causes deformation and weak adhesion.

  • In order to suppress bubble formation, slightly raise the portion not being pressed by the squeegee away from the base. Tilt the squeegee between 40 and 50° (in the pushing direction) and between 30 and 45° (in the pulling direction), and apply 20 to 30 N (2 to 3 kg, 4 to 6 lb) of pressure at a velocity of 3 to 7 cm/sec. while pushing out the air.

    NOTICE:

    While using the squeegee, do not change the speed, stop the operation or change the force of the application. Doing so could cause a streak, called a shock line, across the surface of the black out tape. While using the squeegee, keep the speed and force of application constant and the angle correct.

    HINT:

    • The squeegee can be tilted in either the pushing direction or in the pulling direction against the attachment portion.
    • Perform the procedure while peeling the backing paper off the black out tape, 10 to 20 mm (0.394 to 0.787 in.) from the end of the squeegee.


(5) Application method (method of squeegee operation).

  • If the tape cannot be pressed in one step using the squeegee, perform the application in several steps. Using your finger or a thicker part of the squeegee, gradually apply the tape to the rounded hemming portion in 2 or 3 steps.

    HINT:

    Peel off the backing paper at the hemming portion and apply the black out tape with your finger or a thicker part of the squeegee.

(6) Application method (method of squeegee operation and application method for corner sections).

  • Peel the backing paper off the corner section and carefully apply the tape using a finger.
  • In order to prevent deterioration in appearance caused by the tape pin angle, turn in the tape at the corner after heating the black out tape with a dryer.

(7) Inspection.

  • If the black out tape is not smooth, repeat the application using new black out tape.

    NOTICE:

    Do not use a needle to remove bubbles in any glazed tape being applied to the outer panel, in order to prevent scratches.

    HINT:

    Use an instant adhesive if the hemming or corner portions of the black out tape are partially peeled off.

(b) Clean the attachment surface (using an infrared light).

(1) Using an infrared light, heat any black out tape and adhesive remaining on the body.

CAUTION:

Do not burn yourself on the hot front door panel or with the infrared light.

(2) Using a piece of cloth, rub the remaining black out tape and adhesive off the body.

(3) Using a non-residue solvent, clean the attachment surface.

(c) Clean the attachment surface (using a tape removal disc).

(1) Set the 8 discs in the holder and insert the removal disc into an air drill or electric drill.

NOTICE:

Use an electric drill of which the no-load operation is 2000 to 3000 rpm.

(2) Using a tape removal disc, rub the remaining black out tape and adhesive off the body.

NOTICE:

  • Wear protective glasses during the operation.
  • Rotate and operate the disc in the correct direction.
  • Visually check that the cutting portion is not damaged while rubbing the remaining black out tape and adhesive off the body.

(3) Using a non-residue solvent, clean the attachment surface.

(d) Apply new No. 1 black out tape to the positions shown in the illustration.



Installation Position:

Mark

Measurement

a

2.0 mm (0.079 in.)

b

1.0 or less mm (0.039 or less in.)

c

3.0 mm (0.118 in.)

2. INSTALL FRONT DOOR GLASS RUN

HINT:

Use the same procedure as for the RH side DOOR / HATCH: FRONT DOOR: REASSEMBLY (2008 Sequoia)+ .

3. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: INSTALLATION (2008 Sequoia)+

4. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY MIRROR (EXT): OUTER REAR VIEW MIRROR: INSTALLATION (2008 Sequoia)+

5. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

HINT:

Use the same procedure as for the RH side DOOR / HATCH: FRONT DOOR: REASSEMBLY (2008 Sequoia)+ .

6. INSTALL FRONT ARMREST BASE UPPER PANEL

HINT:

Use the same procedure as for the RH side DOOR / HATCH: FRONT DOOR: REASSEMBLY (2008 Sequoia)+ .

7. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

HINT:

Use the same procedure as for the RH side DOOR / HATCH: FRONT DOOR: REASSEMBLY (2008 Sequoia)+ .

8. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

HINT:

Use the same procedure as for the RH side DOOR / HATCH: FRONT DOOR: REASSEMBLY (2008 Sequoia)+ .